How to Apply Self Tan Around Facial Hair Without Stains

How to Apply Self Tan Around Facial Hair Without Stains

A decent beard should not come with a dodgy fake-tan outline. Applying self tan around facial hair is simple once you stop treating your beard like it is not there. The goal is not to tan every hair on your face. It is to give the skin around it an even, healthy-looking colour, without dark beard hairs, orange sideburns or a pale halo along the jaw.

Whether you have a sharp bit of stubble, a full GAA-season beard or something in between, a small bit of prep makes all the difference. Here is how to get it right.

Why facial hair makes self tan trickier

Self tan develops on the outer layer of your skin, but facial hair gets in the way. A thick beard can block product from reaching the skin beneath it, while dry skin around the beard line can grab too much tan. Add beard oil, moisturiser or a rushed application into the mix and you can end up with patches that look more accidental than sun-kissed.

The good news is that you do not need to force tanning mousse into a full beard. In most cases, the exposed skin on your cheeks, upper lip, jaw and neck is what people see. Get those areas blended properly and your tan will look natural.

Stubble is a slightly different story. Short facial hair does not block as much product, but it can hold onto mousse if you use too much. That can make darker stubble appear temporarily darker or leave product sitting around the roots. Less product and better blending wins every time.

Prep your face before self tan around facial hair

The cleanest result starts before the mitt comes near your face. Wash your face with a gentle cleanser and make sure there is no beard oil, balm, wax or heavy moisturiser left around the beard line. These products create a barrier, which can cause the tan to develop unevenly.

If you shave, do it the night before where possible. Shaving exfoliates the skin, and freshly shaved areas can be a little sensitive or dry. Applying tan straight after a close shave can leave it catching in odd places, particularly under the jaw and around the top lip. Giving your skin a few hours to settle is the safer shout.

Dry patches need attention, especially beside the nostrils, at the corners of the mouth and along the beard line. Apply a tiny amount of plain, lightweight moisturiser to these areas and let it sink in fully. You want to soften dry skin, not coat your face in a slippery layer.

If your beard is full and you are worried about staining the hairs, you can smooth the smallest amount of moisturiser through the very outer edge of the beard. Keep it light. Too much creates a pale, obvious border that is nearly as noticeable as a tan-stained beard.

How to apply self tan around facial hair

Use the leftover product on your tanning mitt after doing your body, rather than pumping a fresh mound of mousse straight onto your face. Facial skin needs far less product than your arms or legs, and a light layer is easier to build than an overdone one is to fix.

Start at the forehead and work down over the temples and cheeks using soft, circular motions. As you approach facial hair, use the edge of the mitt and gradually reduce pressure. Think of it as blending the tan into the beard line, not drawing a hard border around it.

For a short beard or stubble, lightly buff over the hair growth once or twice. Do not scrub product into it. A little colour on the skin beneath the stubble helps the face look even, but soaking the hairs in mousse is unnecessary and can look muddy while the tan develops.

For a fuller beard, keep the product mainly on the exposed cheeks, forehead, nose and neck. Blend just to the edge of the beard, then use a clean, slightly damp cotton bud or corner of a towel to tidy any mousse that has sat on the hairs. The same goes for the moustache. A natural tan should frame your beard, not make it look like it has been dipped in tea.

Do not forget the neck and jaw

A pale neck below a tanned face is a dead giveaway, particularly if you keep your beard short or clean up the neckline. Blend down from the jaw over the neck using whatever remains on the mitt. If your beard runs onto your neck, work around the outer edges and lightly blend over sparse areas.

Check both sides of your face in good light before you are finished. Sideburns, the area under the ears and the corners of the jaw are easy to miss. No need for forensic investigation, but a quick mirror check saves you from discovering a rogue stripe in the pub loos later.

The best approach for different beard lengths

Your application should match the amount of facial hair you have. With clean-shaven skin, apply a light, even layer across the whole face and blend carefully around the nostrils, eyebrows and hairline. The main risk is product gathering in dry spots, not the beard itself.

With designer stubble, treat the face almost as normal but use less product around the jaw, upper lip and chin. Buff gently with the mitt rather than rubbing hard against the grain. This gives the skin colour without loading the stubble with mousse.

With a short, shaped beard, concentrate on the visible skin and gently fade into the top of the cheek line and neckline. The aim is for your complexion to meet the beard naturally. A sharp beard line does not need a sharp tan line beside it.

With a thick beard, there is no point trying to tan the skin buried underneath. Focus on the forehead, cheeks, nose, ears and neck. If you later shave the beard off, exfoliate and reapply your tan properly rather than relying on whatever made it through the forest.

Common mistakes that cause stains and patchiness

The biggest mistake is using too much product. A heavily loaded mitt makes it hard to control where mousse lands, and facial hair catches it quickly. Always begin with less than you think you need.

Applying straight over beard oil is another classic. Oil can stop the tanning ingredient developing evenly, giving you strange light patches right where you wanted definition. Start with clean, dry skin and save the beard oil until after your tan has developed.

Do not use a thick line of petroleum jelly around your beard unless you are only protecting a very specific spot. It can block tan completely and leave a pale outline. A tiny amount of lightweight moisturiser is usually easier to blend.

Finally, avoid touching, scratching or combing your beard while the tan is developing. If mousse has transferred onto the hairs, gently remove it at the time of application. Do not keep fiddling with it afterwards. Hands off, lad.

If self tan gets on your beard

Do not panic. Fresh product is far easier to remove than developed product. Use a damp cloth, cotton pad or cotton bud to wipe the affected hairs straight away, then lightly pat the edge of the skin to keep the blend soft. Avoid soaking the whole area, as this can create a patch in the tan around the beard.

If you only spot it after the tan has developed, wash the beard with a gentle cleanser or shampoo and warm water. A few washes usually lift most of the colour from the hair. Do not attack your face with harsh exfoliants or scrub the skin raw trying to fix it. A slightly darker beard for a day is better than an irritated red face.

Keep the colour looking natural

Once your tan has developed, use a gentle facial moisturiser daily. Hydrated skin holds colour more evenly and fades without the blotchy look that nobody asked for. When applying moisturiser around facial hair, press and smooth it in rather than aggressively rubbing at the beard line.

If you are topping up your colour, keep the face lighter than the body if that suits your natural complexion. Men often overdo the face because it is the bit they inspect closest in the mirror. A subtle, even tan around your beard looks fresher than a face that arrives in the room five minutes before you do.

A quality tanning mousse, such as Brotan's, plus a clean mitt and a bit of patience is all you need. Keep the product light, blend into the beard rather than against it, and let your grooming do the talking.